Tasco-safety.com- Hard hat safety standards

Hard Hat Standards ANSI-Z89.1-1997 Standard Highlights

If you are a hard hat wearer, you should know a few things about the new ANSI Z89.1-1997 Standard for Industrial Protective Helmets:
The standard kind of hard hat you've worn for years is now called a Type I helmet, a helmet that provides protection for the top of your head.
Helmets that provide some degree of top and off-center protection are addressed in the new ANSI Z89.1-1997 Standard and are called Type II helmets.
Helmet wearers must decide whether or not the Type I (top impact) helmet you currently use meets your requirements, or if your work conditions warrant a Type II (top and lateral impact) helmet.
The Standard provides minimum performance requirements

to reduce the forces of impact and penetration from falling objects, and
where applicable, to provide protection from electrical shock hazards

Suggestion: Print this material for future reference.

Compare the New Performance Requirements for Type I and Type II Helmets to the Previous 1986 (ANSI) Standard

Requirement Test Criteria
1986 Edition Test Criteria
1997 Edition

Impact energy attenuation Measures helmet crown's capability to reduce the force of an impact from falling objects to the top of a wearer's head Impact resistance
Product tested in the "as worn" position

8 lb. steel ball dropped at a free fall height of 5'

1000 lb. maximum transmitted peak force to head form

850 lb. maximum transmitted average force to head form

Tested at 0° F and 120° F Force transmission
Helmet Types I & II Product tested in the "as worn" position

8 lb. steel ball dropped at a free fall height of 5'

1000 lb. maximum transmitted peak force to head form

850 lb. maximum transmitted average force to head form

Tested at 0° F and 120° F

Apex penetration Measures helmet crown's capability to resist penetration Product tested within 3" circle on top of helmet in "as worn" position

1 lb. plumb bob, with 35º angle, dropped from a simulated free-fall height of 10'

Depth of penetration (perpendicular distance into thickness of shell)--Classes A & B: pierced not more than 3/8 inch --Class C: pierced not more than 7/16 inch Helmet Types I & II Definitions expanded; new test protocol section, including preparation, mounting, number, and sequence of test samples; summary of failure criteria.

Product tested within 3" circle on top of helmet in "as worn" position

2.2 lb. pointed steel penetrator, with 60º angle, dropped from a simulated free-fall height of 8'

Penetrator can't make contact w/ head form

Test apparatus includes electronic contact indicator, velocity indicator, & electronic recording equipment

No differentiation for helmet Classes

Electrical insulation Measures electrical shock resistance capability of helmet Class B is tested for force transmission first, then tested at 20,000 volts for 3 minutes, with 9 milliamps maximum leakage; then tested at 30,000 volts, with no burn-through permitted.

Class A is tested at 2,200 volts for 1 minute, with 3 milliamps maximum current leakage.

Class C is not tested for electrical resistance. Helmet Types I & II (1) Class E (Electrical) helmets intended to reduce the danger of exposure to high voltage electrical conductors, proof tested at 20,000 volts. Class E is tested for force transmission first, then tested at 20,000 volts for 3 minutes, with 9 milliamps maximum current leakage; then tested at 30,000 volts, with no burn-through permitted. (formerly Class B)

(2) Class G (General) helmets intended to reduce the danger of exposure to low voltage electrical conductors, proof tested at 2,200 volts.Class G is tested at 2,200 volts for 1 minute, with 3 milliamps max. leakage. (formerly Class A)

(3) Class C (Conductive) helmets not intended to provide protection from electrical conductors. Class C is not tested for electrical resistance. (no change in class designation)

Additional Information about the Lateral Protection Portion (Type II Helmets) of the New ANSI Z89.1 Standard

Requirement New 1997 Edition Test criteria

Impact energy attenuation -- Measures the energy-absorbing capability of a helmet from lateral impact Type II (top & lateral impact)

Helmets intended to reduce the force of impact resulting from a blow received off-center or to the top of a wearer's head. Minimum performance criteria:

A helmeted head form (11 lb.) is dropped onto two types of steel anvils, flat and hemispherical

150 maximum peak "G"

Off-center penetration -- Measures lateral penetration resistance capability of a helmet; same procedure as apex penetration except for test location Type II only Test protocol section, including preparation, mounting, number, sequence of test samples; summary of failure criteria. Product tested in the "as worn" position

2.2 lb. pointed steel penetrator, dropped from a simulated free-fall height of 4' and impacted anywhere above the test line

Penetrator cannot make contact with head form

Chin strap retention -- Measures the ability of a chin strap to retain a helmet on a wearer's head Type II only

Note: standard does not mandate the requirement for a chin strap. However, if a chin strap is used, it must meet these requirements. Product tested in the "as worn" position 22.2 lb. mass is attached to the chin strap and dropped from a height of 4" Strap cannot detach from the helmet or elongate more than 1" Strap cannot be less than 0.5" in width

Head Protection Help Center

Glossary of Terms

Hard Hat Standards

Maintenance Information

Head Protection Pages

  Page 01     Page 02     Page 03     Page 04     Page 05     Page 06     Page 07     Page 08
  Page 09     Page 10     Page 11     Page 12     Page 13     Page 14     Page 15     Page 16
  Page 17     Page 18     Page 19     Page 20     Page 21     Page 22     Page 23     Page 24

Other Product Lines

  Ergonomic Products

  Eye Protection

  Fall Protection

  First Aid

  Head Protection

  Hearing Protection

  Mechanix Products

  Protective Clothing

  Respirators

  Safety Dispensers

  Safety Posters

  Safety Signs

  Safety Vests

  Team Hard Hats

  Work Gloves